AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |
Back to Blog
![]() I followed your instruction but I can not get it to work. Finally when you add the camera into QVR Pro make sure you use the HTTP Port (80) as some cameras (Reolink) require you to use the Server Port (8000) Go figure I guess these settings are required for the initial setup / configuration of the cameras. Once it tested valid and it showed up okay I was able to then backout the "Enable Hikvision-CGI, TLS 1.1, Websock(s). I had to then go back to the cameras and "Enable Hikvision-CGI" with Digest/Basic, Enable TLS 1.1, WebSocket and WebSockets, then reboot before I got a valid test and was able to configure the camera through QVR. Funny thing I blew away my version of QVR and started over again with an import of my cameras and I could not get a valid test. ![]() If you wish you can disable the older TLS 1.1 in NETWORK > ADVANCED > Network Service > Disable TLS 1.1 Ensure you have SYSTEM > SECURITY > WEB Authentication > MD5 (QVR doesn't appear to support SHA256 Ensure you have NETWORK > ADVANCED SETTINGS > "Entegration Protocol" > Add > Add the account you are going to use in QVR for adding the Camera, it's not going to allow you to use the account you log on to the Hikvision Camera home page with. Ensure you have NETWORK > ADVANCED SETTINGS > "Entegration Protocol" > "Enable Open Network Video Interface" checked Yes I am missing the Red Markers and Event notifications (For Smart Events but not Basic Events) in QVR Pro but my solution has always been to have Hikvision Email / Text me when a smart event has been triggered anyway. So long story short I ended up going back to ONVIF for these cameras and am very happy. Not only did I not get choppy audio but I hear the smallest details even better. The key here is I was able to use AAC which magically fixed all my audio issues. And set up a user in Hikvision I was able to get the ONVIF Profile S to work with whatever video and audio configuration I wanted. See ONVIF and AAC later.ģ) Even though some cameras would work to record they would get an error as soon as I created a motion detection rule.Ĥ) Even if I chose cameras that had "Line Crossing" in the compatibility list none of them actually gave my DS-2CD2087G2-L or PCI-T15F2SL the ability to chose line crossing in the Event Rules.ĥ) Once I turned ONVIF on. This would cause the audio to become very choppy especially when there was a car driving by. After two days of trying different "Like" cameras (in QVR Pro) from Hikvision this is what I came up with.ġ) You need to make sure the Video configuration (Resolution, Bitrate, Encoding etc) matches whatever you choose in QVR (this was pretty self explanatory but I thought I would post anyway)Ģ) No matter what camera I chose it seems like QVR Pro would change my Hikvision value for the audio back to G.711ulaw. I am certain I must be missing some configuration on the Hikvision camera that will allow QVR to connect via ONVIF. Anyone have any tricks to get this to work as either Model=Hikvision Model=xxxx or Make=ONVIF Model=ONVIF ProfileS cameras etc.? ![]() I can however get it to connect via RTSP. ONVIF S or T is fine for me with this camera but for some reason I cannot get it to work like my DS-2CD2386G2-IU. I HAVE enabled "Open Network Video Interface" and "Hikvision CGI". I was hoping I could add this PCI-T15F2SL in the same way. I have had to add my DS-2CD2386G2-IU's by using "Brand=ONVIF" and "Model=ONVIF ProfileS Cameras" which works fine (I only get basic events) not the smart events. It's NOT on the compatibility list (DS-2CD2386G2-IU isn't sold in America anymore for some reason so I bought this) but none of my other Hikvision cameras are connected using "Brand=Hikvision" "Model=DS-2CD2386G2-IU" in Add Device anyway (all using ONVIF). ![]() Set the NAS on DMZ to make sure router wasnt messing something upĮDIT: Forgot to mention I can connect and view both NAS on the desktop QVR Pro client without issue.I just bought a new Hikvision PCI-T15F2SL which supports ONVIF S and T profiles. I have tried completely deleting and reinstalling the app on both the iPhone and NAS and no luck Has any seen this or have any ideas on how to fix it? Any help or recommendation would be great! Thanks!īoth NAS on 4. I have no idea why the iOS app would work fine on one NAS but completely crash on the other NAS. This also happens on a different iPhone and an iPad. When the app connects I get a black screen on my phone for a split second and then the app crashes.It closes and returns back to my iPhone home screen. However, when I try and connect to my other NAS a TVS-471 the app will allow me to set up the NAS and then connect. One is a TVS-882 and the QVR Pro iOS app works great and have no issues. I have setup the QVR Pro app on 2 different QNAP NAS.
0 Comments
Read More
Leave a Reply. |